Proto-Pasta Cloverleaf Metallic Green HTPLA 3D filament Canada
Proto-Pasta Cloverleaf Metallic Green HTPLA 3D filament Canada
Proto-Pasta Cloverleaf Metallic Green HTPLA 3D filament Canada
Proto-Pasta Cloverleaf Metallic Green HTPLA 3D filament Canada

Cloverleaf Metallic Green HTPLA - 1.75mm - 0.5 KG

$34.00

SKU: 03-B1-D-3539 Proto-pasta

Sold Out

No luck required for great print quality with Cloverleaf Green!

We captured the luck of the Irish in this brilliant green loaded with gold metallic fleck! Though subtle, Cloverleaf Metallic Green HTPLA is loaded with a "pot o' gold", shifting the color towards a warmer, more plant-like green.  Not that you would guess the material's natural, bio-based origin from it's aesthetic.  Cloverleaf Green is not short on gloss and has a paint-like finish reminiscent of a vintage sports car. In any case, be confident that no luck is required for a top-quality finish in anything you print using this material!
Print with the ease of standard PLA with standard hardware and temperatures, but make fun, mesmerizing prints that stand out.  Celebrate good times with ornaments, disco balls, toys, and treasures.  If you want to make a print more fun, just add glitter.  Glitter Flake has little risk of clogging or wearing your nozzle, and it won't make a glitter mess, but beware, printing with glitter is sure to be addictive!  Glitter particles will lay flat with smaller layers, giving top/bottom surfaces more shine than sidewall, so have some fun playing with resolution to see how the result changes!
Like our other HTPLAs, Metallic HTPLA can be "Heat Treated"  to increase crystallinity for "Higher Temperature" resistance compared to amorphous PLA, ABS, and co-polyesters like PETG!  Glittler Flake HTPLA prints translucence, but turns opaque when heat treated (or crystallized).  With a more crystalline structure, heat treated HTPLA parts can hold form to near melting, though temperatures where the material is practically useful vary greatly depending on geometry and load conditions!
For this improved the performance, your prints should be baked in an oven until you see a change from translucent to opaque with reduced gloss.  This visual change indicating the improved performance! We've  seen the change take place in 5-10 minutes on thin walled parts but can take an hour or more.  We've had good luck in a quality, at home convection oven at 110C (225F).  Parts will get very "floppy" before becoming more firm, so please leave supports on your parts or support them and bake them on a flat, non-radiating surface (like glass, ceramic, or composite).

No abrasive fillers so expect normal wear with standard nozzles.

STORAGE: One large resealable bag with slider + an extra desiccant pack are included with every spool. The bag and extra desiccant are a great way to safely store your filament spool when not in use. It keeps your filament bone dry & free from any dust or dirt particles, so it's always ready for your next print.

 3d filament net weight NET WEIGHT: 0.5 KG (1.1 LB)

3d printing temperature guideline Printing
Temperature:

Notes:
190°C - 225°C
  • No special hardware or nozzles are required
  • Prints like PLA on non-heated beds.
  • In our experience, good results were achieved using standard PLA parameters ranging from 190-225C nozzle with standard build surface preparation (blue tape, glue stick, or BuildTak). No heated bed required but up to 60C okay. Beware, if the bed temperature is too high, your part base could actually heat treat while printing, increasing warping and decreasing adhesion. Some shrinkage will occur in the heat treating process, so dimension critical parts may need to be scaled appropriately (as much as 2.5% in our experience).